Stainless liners, caps, and flashing fixed by chimney pros
Metal chimney repair in Randolph Town that stops leaks for good
When your metal chimney rusts through, leaks at the flashing, or backs smoke into the house, you need metal chimney repair in Randolph Town from someone who works on steel and stainless systems every week. We handle everything from a pitted cap to a full metal chimney replacement in Randolph Town, and we do it on homes across Randolph Town, Massachusetts. Call (844) 803-2151 and we'll get eyes on it fast.
Live phone supportUpfront optionsBacked workmanship
What's included
What's included in metal chimney repair
Every metal chimney repair job includes a full inspection, the repair itself, and a draft test before we leave. Here's what's covered in a standard visit, and what we quote separately if the scope grows.
Camera inspection of the flue
We run a camera inspection system down the full length of the flue to check for cracked, separated, or rusted liner sections. You get the photos and a plain explanation of what we found.
Cap and storm collar service
The cap and storm collar are the most common failure points on a metal chimney. We replace damaged caps and reseal or replace storm collars with new hardware matched to your system.
Flashing repair or replacement
Failed flashing is where most leaks start. We pull the old flashing, install new material, and seal it correctly against the roof so water can't track under it.
Liner section replacement
When individual stainless steel liner sections have cracked or separated, we replace them and re-secure the joints. This is often far cheaper than a full metal chimney replacement in Randolph Town.
Draft and smoke test
Before we leave, we run a draft test to confirm the flue pulls correctly and there's no smoke backup. If the draft is off, we find out on our time, not yours.
Photo documentation
You get photos of the flue, cap, flashing, and anything we repaired. It's useful for insurance, for resale, and for knowing exactly what's on your roof.
Service overview
What metal chimney repair in Randolph Town actually involves
Metal chimney repair in Randolph Town is the diagnosis and correction of a factory-built or stainless steel chimney system, covering the cap, storm collar, flashing, liner sections, and the joints where water gets in. We start with a camera inspection system to see inside the flue, then check the cap, chase cover, and roof flashing for rust-through and failed sealant. From there it's a matter of replacing what's failed, resealing what's sound, and confirming the whole system meets NFPA 211 clearances before we leave.
Most of the calls we run in Randolph Town come from three things: rust at the cap and storm collar, water tracking down a failed chimney flashing, and liner sections that have cracked or separated after years of heating cycles. If you've been searching for metal chimney repair near me in Randolph Town Massachusetts and getting nothing but roofers who don't touch flues, that's the gap we fill. We also quote metal chimney replacement cost Randolph Town homeowners can plan around before we start.
How we workWe verify the cause, compare realistic options, and confirm the repair before we leave.
The service timeline
How our metal chimney repair process runs
The process flexes to the condition, but these checkpoints keep decisions clear.
Call and schedule
You call (844) 803-2151 or book online. We ask what you're seeing, water stains, smoke backup, rust flakes in the firebox, and set a window. Most Randolph Town jobs get a same-week slot, and we text you when the tech is on the way.
Roof and flue inspection
The tech lays drop cloths inside, then goes up top. We run a camera inspection system down the flue, check the chimney cap, storm collar, flashing, and chase cover, and photograph anything that's failed. Takes about 45 minutes on a typical ranch or colonial.
Written findings and price
You get the photos, a plain-English explanation of what's wrong, and a fixed price for the repair. If replacement makes more sense, we quote that too so you can compare. No surprises added later.
The repair itself
Cap and flashing repairs run one to two hours. Liner section replacements take three to five hours. We use stainless steel liner components from DuraVent or Selkirk, new flashing, and chimney cap hardware matched to your existing system.
Test and walkthrough
Before we pack up, we run a smoke or draft test to confirm the flue pulls correctly, check every joint we touched, and walk you through what we did. You get the photos and a workmanship warranty on the repair.
Tools & methods
Tools and methods we use
Purpose-built equipment, used by trained technicians, so the job is done accurately the first time.
Camera inspection system
Lets us see the full length of the flue without tearing anything apart. We use it on every metal chimney inspection to find cracked or separated liner sections.
Chimney brush and rods
Sized to your flue diameter, these remove creosote and debris before any repair work. We follow with a HEPA vacuum to keep the house clean.
Grinder with diamond blade
Used when we need to cut or shape masonry around a metal flue penetration, or trim a chase cover to fit a new cap.
Masonry drill
For anchoring new flashing, cap hardware, and chase covers into brick or block without cracking the surrounding masonry.
Drop cloth and HEPA vacuum
Interior protection on every job. We lay drop cloths before we start and vacuum with a HEPA unit when we're done, so you don't find soot later.
Mortar jointer and tuckpointing trowel
For repointing the masonry chase around a metal flue when the mortar joints have failed and water is getting in behind the brick.
Use cases
When Randolph Town homeowners call us
These examples show how the service framework adapts rather than forcing every call through one repair.
Separated liner sections, Randolph Acres
A wood stove setup where two stainless liner sections had separated at the joint after years of heating cycles. Smoke was backing into the room on every cold start, and the homeowner was worried about carbon monoxide. → Both failed liner sections replaced with new stainless steel liner matched to the stove. Joints re-secured and the full flue camera-inspected. Draft test passed on the first try, and the smoke backup stopped immediately.
Failed flashing leak, Randolph Center
A colonial with water tracking down the chimney chase and showing up as a stain on the second-floor ceiling. Two previous attempts to seal the flashing from the outside hadn't worked. The actual failure was under the flashing, not on top of it. → Old flashing pulled, new flashing installed and sealed correctly against the roof deck, and the chase cover resealed. Water test confirmed the leak was fixed. The ceiling stain was dry within two weeks and didn't return the following spring.
Problems we solve
Metal chimney problems we fix in Randolph Town
Most metal chimney calls come down to water, rust, or draft. Here are the ones we see most often in Randolph Town and what happens if they're left alone.
Water staining on the ceiling near the chimney
We trace the leak to its actual source, usually the flashing or storm collar, and repair it with new material. Then we confirm with a water test before we leave so you know it's actually fixed.
Rust flakes in the firebox or on the roof
We inspect the cap, storm collar, and liner for rust-through. Surface rust gets cleaned and resealed. Sections that are compromised get replaced with new stainless steel liner components.
Smoke backing into the house when the fire is lit
We run a camera down the flue, check the damper, and find the actual cause. Most draft problems trace back to liner damage or creosote buildup, and both are fixable in one visit.
Chimney cap bent or missing after a storm
We install a new stainless or copper cap sized to your flue and reseal the storm collar underneath. Most cap jobs are done in under two hours.
Pricing process
What metal chimney repair costs
$250 - $900 for most repairs; $2,200+ for full metal chimney replacement
Chimney height and roof pitch
A steep roof or a tall chimney adds setup time and safety rigging, which raises labor. A single-story ranch with a gentle pitch is the fastest, cheapest scenario.
Scope of the failure
A cap and storm collar job is a fraction of the cost of a multi-section liner replacement. We quote based on what's actually failed, not a flat rate.
Parts and materials
Stainless caps and liner sections cost more than aluminum, but they last far longer. We quote both options when it makes sense so you can decide.
How much does metal chimney repair cost in Randolph Town Massachusetts?
Most metal chimney repairs in Randolph Town run $250 to $900 in 2026, depending on what failed. A cap or storm collar replacement sits at the low end, around $250 to $450. Flashing repairs run $350 to $700. Liner section replacements push toward the top of the range. Full metal chimney replacement typically starts around $2,200 and goes up from there based on height and liner length.
Can a metal chimney be repaired in Randolph Town?
Yes, in most cases. Caps, storm collars, flashing, and individual liner sections can all be replaced without tearing out the whole system. The exception is a flue that's rusted through in multiple sections or has failed at the joints, where replacement is the safer call. We inspect first, show you the photos, and tell you honestly which one you're looking at.
What is metal chimney replacement in Randolph Town Massachusetts?
Metal chimney replacement means pulling the old factory-built or stainless system and installing a new one, usually a DuraVent or Selkirk assembly matched to your appliance. It's the right call when the existing flue has rust-through, cracked liner sections, or clearances that can't be corrected. Most replacements take one full day and include a new cap, flashing, and storm collar.
Who does metal chimney repair near me in Randolph Town?
We do. FixoraPoint handles metal chimney repair across Randolph Town and the surrounding neighborhoods, from Downtown Randolph to Randolph Heights and Randolph Woods. Call (844) 803-2151 and we'll schedule an inspection, usually within the same week. If it's an active leak or smoke backup, tell us on the phone and we'll prioritize it.
Related services
Related Services
chimney repair near me
General chimney repair covers the masonry, crown, and flashing work around your metal flue. If your metal chimney repair in Randolph Town turns up cracked brick at the crown, we handle both in one visit so you're not scheduling two crews.
chimney masonry repair
Metal chimneys often sit inside a masonry chase. When that brick spalls or the mortar joints fail, water gets to the metal. We repair the masonry and reseal the chase so the metal system stays dry.
chimney crown repair
A cracked chimney crown lets water run down the chase and into your metal flue joints. We rebuild or reseal the crown with chimney crown mix as part of a full metal chimney repair in Randolph Town when the crown is the water source.Ready when you are
Get metal chimney repair in Randolph Town scheduled today
We're licensed, insured, and we've been fixing Randolph Town chimneys since 2022. Call now and we'll get a tech on your roof, usually within the same week, with a fixed price before any work starts.
Talk with the local team
Request metal chimney repair
Call (844) 803-2151 or email [email protected] and tell us what your chimney is doing. We answer the phone 24/7 for emergencies and schedule routine repairs within the same week. If you are not sure whether you need a repair or just a sweep, we will tell you straight.